Parasound AVC-2500 User Manual Page 41

  • Download
  • Add to my manuals
  • Print
  • Page
    / 63
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 40
41
To Automatically Set the Analog Input Level:
1. Play material through the input source. Select source material with loud transient peaks.
2. Press and hold the Setup/Trim button on the remote control until SOURCE SETUP appears
on the front panel or on-screen display.
3. Press the Tune < or > buttons until ANALOG INPUT appears in the displays.
4. Press the A.Cal button on the remote until graphic level meters appear in the displays.
You do not need the calibration mic for this procedure.
5. The AVC-2500 will automatically adjust the analog input level to an optimum setting in
about 30 seconds.
6. Press the Tune > button to advance to the next SOURCE SETUP procedure, or press and
hold the Setup/Trim button for three seconds to return to normal operation.
Setup Menu Level Two - Bass Management
Bass management is designed to assure overall balanced bass response by accommodating
many different types of speaker systems that may or may not be able to reproduce frequencies
below 80 Hz. The Bass Management setup menu lets you configure all of your speakers to
accept low frequencies below 80 Hz, or to filter out these frequencies and route them to your
front speakers, or send them only to your subwoofer channels. THX certified speaker systems
should always be set to "SMALL/THX for the left, right, center, and surround outputs.
Additionally, there should always be a subwoofer in a THX speaker system
To Setup Bass Management for Your Front Left and Right Speakers:
1. Press and hold the Setup/Trim button on the remote control until SOURCE SETUP appears
on the front panel or on-screen display.
2. Press Setup/Trim again until BASS MGMT SETUP appears in the displays. If you are
continuing from the previous setup menu, you only need to press Setup/Trim again.
MAIN: and LARGE appear in the displays.
3. Refer to the owner’s manual of your front left and right speakers to determine whether
they are designed to reproduce frequencies below 80 Hz.
4. If the Main (Left and Right) speakers are designed to handle frequencies below 80 Hz,
press the Volume
g g
g g
g or
h h
h h
h buttons to select LARGE . The front left and right speakers will
operate full range (20 Hz to 20 kHz).
5. If they were not designed for low frequencies, select SMALL/THX. The front left and right
speakers will have low frequencies rolled off 12 dB per octave starting at 80 Hz.
6. Press the Tune
e e
e e
e button to advance to center channel bass management options, or
press and hold the Setup/Trim button for three seconds to exit BASS MGMT SETUP and
return to normal operation.
To Setup Bass Management for Your Center Speaker:
1. If you are not already in the Bass Management setup menu, follow steps 1 and 2 from
above and use the Tune
f f
f f
f or
e e
e e
e buttons until CENTER and LARGE appear in the displays.
2. Press the Volume
g g
g g
g or
h h
h h
h buttons to select either SMALL/THX, LARGE, or NONE.
3. Refer to the owner’s manual of your center speaker to determine whether it is designed
to reproduce frequencies below 80 Hz.
4. If the center speaker is designed to safely reproduce frequencies below 80 Hz, select
LARGE. The center speaker will operate full range (20 Hz to 20 kHz).
5. If it is not designed for low frequencies, select SMALL/THX. The center speaker will have
low frequencies rolled off 12 dB per octave starting at 80 Hz. This low frequency
information is then re-routed to the subwoofer channel.
6. If you do not have a center channel speaker, select NONE and the AVC-2500 will create
a phantom center image using the front left and right speakers.
7. Press the Tune
e e
e e
e button to advance to surround channel bass management options, or
press and hold the Setup/Trim button for three seconds to exit BASS MGMT SETUP and
return to normal operation.
Page view 40
1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 62 63

Comments to this Manuals

No comments