Parasound AVC-2500 User Manual download pdf (Page 15)

1. On-Off Button

This button turns the AVC-2500 On and Off.

2. Digital Selection Buttons

The Digital

g g

g and

h h

h buttons allow you to scroll up or down

through all six digital inputs and the analog input.

3. Surround Selection Buttons

The Surround

g g

g and

h h

h buttons allow you to scroll through

all five Autoformating Surround Processing (ASP) modes:

Cinema, Stereo, Music, Party, and Mono.

4. THX/Dynamic Range Control Buttons

THX Button

Press the THX button to add THX processing to ASP modes

including Dolby Digital, Dolby Pro Logic, DTS, and Mono.

Dynamic Range Control Button

The Dyn button engages Dynamic Range Compression that

may be encoded into a digital bitstream. This feature is often

called the nighttime listening mode.

5. Setup/Trim Button

Press this button to enter the setup operation of the AVC-

2500. This button is also used to temporarily trim channel

levels while watching a film or listening to a recording.

6. Volume Buttons

The Volume

g g

g and

h h

h buttons adjust the master volume up

and down in 1 dB steps. These buttons are also used for setup

and trim operation.

7. Mute Button

Press the Mute button to interrupt the audio signal from reach-

ing the output of the AVC-2500. The Mute button does not

affect the record output jacks

8. Tune

f f

f /Auto Audio Button

When the tuner is activated, pressing this button normally

advances to the next preset. If you change the tuning mode,

the Tune

f f

f button selects a lower radio frequency.

When you hold this button down for three seconds, the AVC-

2500 scans for any active digital or analog audio signal and

automatically switches to that input source.

9. Memory Enter Button

The Mem/Enter button is used to store Digital Inputs, THX,

and Dynamic Range Control into Input Sources. This button

is also used during the setup process.

10. Tune

e e

e /Auto Video Button

When the tuner is activated, pressing this button normally

advances to the next preset. If you change the tuning mode,

the Tune

e e

e button selects a higher broadcast frequency.

When you hold this button down for three seconds, the AVC-

2500 scans for any active video signal and automatically

switches to that input source.

11. Tuning Button

Pressing the Tuning button activates the AVC-2500 tuner. It

also changes the tuning mode from manual to automatic. In

the manual mode, frequencies are changed at 50 kHz steps

with the Tune

f f

f and

e e

e buttons. In the auto mode, the next

or previous broacast frequency is selected.

12. Status Button

The Status activates the on-screen display to provide opera-

tional status of the AVC-2500. Press this button again to turn

off the status display.

13. FM/AM/ A. Cal Buttons

FM/AM Button

The FM/AM button toggles between AM and FM frequency

bands.

Auto Calibration Button (A.Cal)

This button engages the Automatic Calibration feature of

the AVC-2500 when the ACM-2500 microphone is con-

nected.

14. Dimmer/Sleep Buttons

Dimmer Button

This button dims the front panel display and indicators by

50%.

Sleep Timer Button

The Sleep button sets the AVC 2500 to automatically turn

off. Each press of the sleep button increases the sleep timer

by 15 minutes for a maximum of 90 minutes.

15. Source Buttons

These buttons provide direct access to all twelve inputs of

the AVC-2500. The Source buttons are labeled Audio (Aud)

1-6 and Video (Vid) 1-6.

16. Numerical Preset Buttons 1-10

Pressing any of these activates the tuner (if not already on)

and selects the radio station programmed to that number.

17. Macro Buttons

These 4 macro buttons allow you to program a series of com-

mands for one touch operation of multiple remote commands.

18. Shift Button

The Shift button accesses several “secondary” codes such as

separate on and off commands.

19. Zone Button

Press the Zone button before a command to issue a Zone

command. For example, Pressing Zone + On-Off turns the

remote Zone On or Off.

20. Light Button

The Light button illuminates the remote control.

21. Programming Status LED

This three-color LED flashes when programming infrared

codes into the learning remote control.

22. Device Buttons

The device buttons allow you to choose different "pages" to

control up to eight components including the AVC-2500.

Note: Press the AVC button to control the AVC-2500.

The Learning Remote Control

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 62 63

Comments to this Manuals

No comments

Parasound AVC-2500 User Manual Page 15

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Parasound AVC-2500